Hourmeters SIM-05ch-2-17(09)

Счетчик импульсов СИМ-05ч-2-17

Счётчик импульсов СИМ-05ч-2-09

17 case 09 case
SIM-05ch-2-17 AC400V UHL4
1990.00 руб. с НДС

SIM-05ch-2-17 AC230V UHL4
1990.00 руб. с НДС

SIM-05ch-2-17 AC230V UHL2
2746.00 руб. с НДС

SIM-05ch-2-17 DC10-30V UHL4
1990.00 руб. с НДС

SIM-05ch-2-17 DC10-30V UHL2
2746.00 руб. с НДС

 
  • Calculation and indication of the total operating time of equipment in hours, minutes and seconds
  • Calculation and indication of the amount inclusions of equipment
  • The ability of reset accumulated indications
  • The ability to read accumulated indications without inclusion of equipment
  • Shield and wall execution of the case
 
 WARNING:  Counter is designed for process control equipment operating time. Counter is not intended for commercial account.
 
PURPOSE OF HOURMETER
 Hourmeters SIM-05ch-2 is designed to account for the total operating time of the equipment and its inclusions in the service.
 
DESIGN OF HOURMETER
 The couter is mounted on a smooth surface (SIM-05ch-2-17) or in a shield (SIM-05ch-2-09). A material of case - impact polystyrene. The front panel has a six-digit indicator. In the counter SIM-05ch-2-17 from below of case are located hermetic inputs for the output of wires that are connected to the equipment. For installation the device it is necessary to secure it with screws and bolts in the hole of the case. At the counter SIM-05ch-2-09 behind is located terminal blocks for wires, that connected to equipment. For installation the device it is necessary to cut out in the panel a window with dimensions 94*94mm, to place the device in the window, to install on the side surface of the device mounting brackets, that included in the delivery, and to attach by screws the device to the panel. Connecting the power of counter is produced to jack X1. When feeding of the counter constant voltage power the connection of wires should be carried out according to the markings on the case. On the terminal A1 is supplied positive power pole.
 
OPERATION OF HOURMETER
 When power is applied to the "INPUT ACCOUNT" the device keeps track of the current number of inclusions and the current time of the equipment, as well as the total number of inclusions and the current total accumulated operating time of the counter and saves these parameters in non-volatile memory when the power is turned off. The information storage time is not limited. When powering on the display is shown the current number of inclusions, and then - current value of the operating time at the time of inclusion and then the current time. Number of involved digits of indicator, set aside for indication of hours, minutes and seconds is determined by the number of actual hours worked. On the indicator digits set aside for hours/minutes/seconds, are separated by dots. As the number of digits, occupied by the counted clock, location of dividing point moves to the right and, accordingly, is reduced the number of least significant bits, originally set aside for indication units of seconds, tens of seconds, units of minutes and tens of minutes.
 When power is applied to the "INPUT INDICATION" device alternately (with a period of 10s) shows the total number of inclusions and the total accumulated time of the account, at the same time the count of time does not occur. That mode allows you to see the value of the operating time without power supply to the equipment.
 While supplying a power to both inputs is produced counting time and is shown the total number of inclusions with a period of switching indication 10s.
 
 Reset of current operating time and number of current inclusions of equipment is produced in the following order:
     - Remove the power from the counter.
     - Remove jumper from contacts JP.
     - Apply power to the counter.
     - Remove power from the counter set the jumper to the contacts JP.
 Beginning of count down starts when you turn on the power.
 
SPECIFICATION OF HOURMETER SIM-05ch-2-17 (09)
A parameter
Unit
SIM-05ch-2-09
SIM-05ch-2-17
Supply voltage
V
AC230
AC400
DC10...30
AC230
AC400 DC10...30
Maximum consumption of sensors
mA
90
The number of digits of display
 
6
Deviation of counting time, not more
%
± 1
The maximum total operating time
h
till 999999
Accounting for the number of starts
 
till 999999
Dimensions
mm
96х96х93
82х80х56
Size of indication window
mm
20х76
14х47
Height of digit
mm
15
10
The degree's protection
 
IP54/IP20
IP54/IP54
Operating temperature range (different versions)
0C
-25...+550C (UHL4)
-40...+550C (UHL2)
Storage temperature
0C
-25...+70
Immunity to interference from bursts in accordance with GOST R 51317.4.4-99 (IEC/EN 61000-4-4)
  level 3 (2kV/5kHz)
Immunity to interference over voltage in accordance with GOST R 51317.4.5-99 (IEC/EN 61000-4-5)
  level 3 (2kV A1-A2)
Climatic modification and placement category by GOST 15150-69 (non-condensing)
  UHL4 or UHL2
The degree of pollution in accordance with GOST 9920-89
  2
Relative humidity of air % up to 80 (at 250C)
Height above sea level m till 2000
Weight, not more
kg
0,35
Operating position in space
  artbitrary
Mode
 
round the clock
Period of storage information when power is off
 
not limited
 
CIRCUIT CONNECTION OF COUNTER
Схема подключения счётчика импульсов СИМ-05ч-2-17
 
DIMENSIONS OF COUNTER SIM-05ch-2-17
Габариты 82*80*56
 
DIMENSIONS OF COUNTER SIM-05ch-2-09
Габариты 96*96*63
 
Title
Order code
File to download
(manual)
File date
SIM-05ch-2-17 АС400V UHL4
4640016935697
v07.04.2016
SIM-05ch-2-17 АС230V UHL4
4640016935680
SIM-05ch-2-17 АС230V UHL2
4640016935673
SIM-05ch-2-17 DC10-30V UHL4
4640016935710
SIM-05ch-2-17 DC10-30V UHL2
4640016935703
SIM-05ch-2-09 АС230V UHL4 4640016935659
SIM-05ch-2-09 DC10-30V UHL4 4640016935666

 

English
You are reporting a typo in the following text:
Simply click the "Send typo report" button to complete the report. You can also include a comment.